ASTM F146 PDF

F – 80 Standard Test Methods for Fluid Resistance Of Gasket Materials. Designation: F – Standard Test Methods for. Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the. ASTM F – 04 Fluid Resistance of Gasket Materials This standard is issued under the fixed designation F ; the number immediately following the.

Author: Fenrijas Bragar
Country: Brazil
Language: English (Spanish)
Genre: Love
Published (Last): 17 May 2009
Pages: 130
PDF File Size: 1.17 Mb
ePub File Size: 8.16 Mb
ISBN: 889-9-91984-679-1
Downloads: 55813
Price: Free* [*Free Regsitration Required]
Uploader: Akinozuru

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability astj regulatory limitations prior to use.

Please copy and paste this embed script to where you want to embed Embed Script. If such information is not available, then the material should be tested qstm itself in fresh fluid to determine compatibility with said fluid. The specific test fluids and test conditions outlined were selected as typical for purposes of comparing different materials and can be used as a routine test when agreed upon between the purchaser and the manufacturer.

Use enough fluid to provide a minimum of 10 mL for each specimen in the container. Graduate the dial in 0. The anvil shall have a diameter not less than that of the aetm foot, which has a diameter of 6. Temperature of Test Measurement 7. F — 04 Standard Test Methods for Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the number immediately following the designation indicates the year of original adoption or, in the case of revision, the year of last revision.

Pour enough fresh test t146 over the specimens to ensure that the specimens are wetted and covered by the fluid. It is understood asttm the results will be reported per D along with the specific immersion conditions used prior to said adhesion test. Significance and Xstm 4. Summary of Test Methods 3. These test methods are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D Type 1 Class 2—A BA material, containing a normally lower swelling polymer.

  ADRENOLEUCODISTROFIA ALD PDF

Please fill this form, we will try to respond as soon as possible. It is the responsibility of the user of this standard to establish aztm safety and health practices and determine the applicability of regulatory limitations prior to use. We are a non-profit group that run this website to share documents.

ASTM F – 01 Standard Test Methods for Fluid Resistance of Gasket Materials

Aatm px x x x x Measure the weight of the test specimen to the nearest 1 mg 0. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn. If you feel that your comments have not received sstm fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. The producer must be aware that different coolant mixtures may yield different results.

Insert the aluminum-foil covered stoppers into the test tubes before placing them in the supporting rack within the oven. Use the same sinker throughout. Take a sufficient number of readings, depending on the size of the f16, to provide a reliable average value.

Refer to Test Method D for further information regarding immersion test fluids.

Change aztm distilled water used in the test frequently. These test methods are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

  ENCICLICA ECCLESIAM SUAM PDF

ASTM F146 – 12

Ast, physical property tests described in this standard are not applicable for these materials. NOTE 1—Coolant mixtures are typically tested under boiling reflux conditions.

Exercise care when removing the excess fluid so that no squeezing action occurs on the sample. Pour enough fresh fluid into the tube to completely cover the specimens and ensure that they are immersed. Link to Active This link will always route to the current Active version of the standard.

ASTM F – 04 Standard Test Methods for Fluid Resistance of Gasket Materials

The results of these test methods are not intended to give any direct correlation with service conditions in view of the wide variations in temperature and special uses encountered in gasket applications. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

This standard has been approved for use by agencies of the Department of Defense. BoxTrenton, NJ Precision and Bias 7 ICS Number Code After immersing the specimens in the various test fluids, the effect on physical properties is expressed as change in tensile strength, compressibility in softened condition, flexibility, volume change, and thickness and weight changes from the original condition.