ASTM B267 PDF

ASTM B Standard Specification for Wire for Use In Wire-Wound Resistors. ASTM-B – Download as PDF File .pdf), Text File .txt) or read online. Non Ferrous Standard. This specification covers round wires and ribbons with controlled electrical properties made from magnetic and nonmagnetic class 1a alloys.

Author: Fenrit Daikora
Country: Indonesia
Language: English (Spanish)
Genre: Automotive
Published (Last): 9 February 2004
Pages: 32
PDF File Size: 19.52 Mb
ePub File Size: 13.17 Mb
ISBN: 537-3-15743-705-2
Downloads: 57375
Price: Free* [*Free Regsitration Required]
Uploader: Meztira

D in Diameter in. This specification covers round wires and ribbons with controlled electrical properties made from magnetic and nonmagnetic class 1a alloys. B — 07 ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. It is informational only and not an official part of the standard; the full text xstm the standard itself must be referred to for its use and application.

It shall include both single and double coverings.

The nominal resistance per unit length for a round wire is calculated from the nominal resistivity and nominal cross-sectional area. Historical Version s – view previous versions of standard. The electrical resistance per unit length can be determined more accurately than the dimensions of very small wire. This is not valid in view of modern rolling equipment and practices, but still is widely used as a basis of description. The tension on the wire shall not exceed one half of its yield strength.

Outside Diameter, max, in. Current edition approved May 1, Caution should be exercised pending knowledge of the maximum temperature of use for the coating material involved. If you feel that your comments have not received a adtm hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

ASTM B Standard Specification for Wire for Use In Wire-Wound Resistors_百度文库

Originally approved in The enamel shall not be underbaked so that one turn adheres to the next on a spool. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. All of the information included in this note is based on measurements made in accordance with Test Method B NOTE 1—When ribbon or?

  BHADANT ANAND KAUSALYAYAN BOOKS PDF

A superscript epsilon e indicates an editorial change since the last revision or reapproval. No further reproductions authorized. Ribbon actually is made to a speci? The second covering shall be wrapped in the opposite direction from the? Temperature Coefficient of Resistance 8.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. C The maximum temperature values listed apply to the alloy wire only. Link to Active This link will always route to the current Active version of the standard.

The test shall be made 2 to 10 min after removal of the wire zstm the oil, lightly wiping off the excess oil. Users of this adtm are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. To convert from inches to millimetres multiply by Each bare wire should conform to the requirements for nominal resistivity, elongation, thermal electromotive force with respect to copper, and the temperature coefficient of resistance contained in this specification.

Maximum indicates the maximum deviation from zero and the plus or minus sign the polarity of the couple. Your comments will receive careful consideration at a meeting of the responsible technical committee, atsm you may attend. The covering shall be sufficiently closely wrapped so that, when the wire is bent around a mandrel having a diameter ten times the overall diameter of the covered wire, using only enough tension to give an even compact layer, the wrappings will not open enough to make the wire underneath visible to the ashm eye.

The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. This abstract asym a brief summary of the referenced standard.

  BUYOLOGY BY MARTIN LINDSTROM PDF

ASTM B267 – 07(2018), Standard Specification for Wire for Use In Wire-Wound Resistors

Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. The wires and ribbons, which may have insulated coverings or enamel coatings, are recommended for use in wire-wound resistance units like precision resistors and other similar applications, but not for use as electrical heating elements.

B — 07 Standard Speci? This slope is determined from the following equation: This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Last previous edition approved in as B — 90 Permissible Variations in Dimensions A number in parentheses indicates the year of last reapproval. Permissible Variations in Electrical Resistance Values shown for other classes are for information only. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

B Alloy Classes 1a, 1b, 1c, 2a, 2b, 3a, 4, and 6 are designed to give a low emf versus copper. It shall be free from voids or bare spots and have a minimum of asrm twist. All alloys covered by these speci? The mean temperature coefficient of resistance referred to Copyright? Alloy Class 1 3 4 5 6 Color purple yellow red pink ivory The surface of the coating shall be smooth and uniform.

ASTM v267 not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Wire larger in diameter than sizes listed in Table 6 may be supplied on spools Table 7 or in coils depending on agreement between the b2677 and the purchaser. It is the responsibility of the user of this standard to become familiar with all hazards including those identi?